Disconnect the dryer from the gas line by unscrewing the flex hose from the line only. Your owner’s manual is a great place to start troubleshooting.
Then remove the old dryers gas line from that pipe.
How to turn off a gas dryer. When replacing the gas dryer with an electric dryer, you must call a professional to permanently cap off the gas line. Gently pull out the dryer until you can get to the vent hose. To disconnect a gas dryer, take the hose off the gas outlet and from the back of the dryer.
Turn off the dryer's gas supply. Disconnect the flexible duct hose that connects the dryer to the exhaust vent. Turn off the dryer’s gas supply.
You can do this by turning off the small valve on the dryer line or the main valve that supplies gas to the whole house. And, dryers are light and very easy to move. Turn the shut off valve off and disconnect the flexible gas connector.
If that is what is. Release the tabs behind the front console. It could be anywhere in the main gas line.
If it’s a gas unit, also turn the gas off. My son says, first, turn off the gas valve and unplug the electricity, but you dont remove the gas line itself from the dryer. You should now see the control board
Reach out to a professional immediately and let him handle the issue. Buy a new hose that is longer than your old one. It is also a good idea to turn the circuit breaker off as another precaution to avoid electrocution.
By joey s earned 77,241 community points in washers If you see a lot of gas leaking out, evacuate immediately. Unplug the dryer from the outlet.
Disconnect the dryer from the gas line by unscrewing the flex hose from the line only. You can do this by turning off the small valve on the dryer line or the main valve that supplies gas to the whole house. If the valve is perpendicular to the main gas line it should be shut, and if it’s in line with the pipe then it should be open.
I added an image below showing the gas valve in the on position, rotate the handle 90 degrees to shut the gas off. Next is to wait for approximately 30 min to make sure that there is no gas left in the dryer then proceeds to shut down the gas supply pipe. A few safety steps and you’re good to go!
Always turn off the gas and disconnect the pipe before attempting to work on a gas dryer. Most commonly, a gasline to a dryer is 1/2 inch. Open the dryer container to remove any lint from the dryer lint screen.
With that, you’ve disconnected your gas dryer from the gas line. Check the main gas line of your house and see if it’s still turned on. Most gas appliances have a gas shutoff valve located near the appliance that lets you turn off the gas to that appliance only.
Place the hose and the ductwork inside the drum if you are planning to move the dryer. Wrap teflon tape around the connection to ensure a complete seal. If it will not turn one direction, turn it the other direction.
Seal the gas line using a gas line cap. Install a 1/2 inch by 3/8's inch ball valve type gas shut off valve directly onto the steel gas pipe threads. Turn of all power to your dryer.
Seal the gas line using a gas line cap. If your gas or electric dryer isn’t ending the auto dry cycle when the clothes are dry, it may be the fault of a defective cycling thermostat. Slide the dryer away from the wall, and remove all screws securing the top panel to the frame.
One of the most important things you can do before replacing the dryer part is to unplug it. You should have a shut off valve behind the dryer with a flexible gas connector from the shut off valve to the dryer. Shut down the gas dryer.
Turn off the gas at the valve in the laundry room by turning it clockwise until it stops. Once every appliance in your home has been turned off, you are safe to turn the gas back on. Use a wrench to disconnect the flex gas line at the shut off valve.
Make sure that there are no clothes inside then turn off the gas dryer and unplug it from the outlet. This part governs the temperature of the dryer as well as the timer motor on auto dry models. Get some magic sliders if you are afraid of damaging your floors.
A defective thermostat may not allow the timer to advance to the off position and continue to run. Don’t forget to turn off the gas to your dryer anytime you are moving it or taking it apart! Also, if you have a gas dryer, you will need to shut off the gas.
If your handy, turn off the main house gas at the meter. In some cases, turning off the gas at the appliance's shutoff valve will suffice if there is a gas leak or the appliance needs to be replaced or serviced. Pull the top panel up and off of your dryer.
You can do this by locating the gas valve to your home and shutting it off until you are finished working. Replace the howe, tucked tightly in the dryer and the vent outlet. You will also need proper tools to open the component to get the timer out.
Then remove any adaptor fitting installed on the gas pipe. Some dryers have a bottom drawer that can be used to access the gas valve. Most will give you potential causes for your dryer's problem as well as providing dryer part and component numbers and outline how to order replacement parts.Read Full Article